One Internet Connection, Every Building Covered

This is different from mesh WiFi, which spreads coverage around inside one building or a tight cluster of buildings using shared nodes. If your problem is a dead zone in the back bedroom, that's mesh. If your problem is a separate structure that WiFi simply can't reach, that's a bridge.

We'll walk your property, talk through what actually needs connecting, and recommend the right mix. Sometimes that's one simple bridge, sometimes it's a hub with several buildings connected off it.

But trenching across paddocks, driveways or any real distance gets expensive fast, and isn't always practical on leased land, near council boundaries, or across ground you don't want dug up. A wireless bridge gets you the same result, one shared connection across both buildings, without the digging, and it's usually a fraction of the cost.

• Line of sight, properly assessed. The two mounting points need a reasonably clear path between them. It's not just about what's directly in the way today, it's what might grow into the way.
• Seasonal thinking. A path that's clear in winter can be blocked by a shelterbelt or orchard canopy once it leafs out in summer. We plan mounting height around the full growing season, not the day of install.
• Mounting height and stability. Antennas mounted too low get blocked by fences, vehicles, or a hedge that's grown six months later. A rigid, properly elevated mount keeps the link aligned through wind and weather.
• The right frequency and equipment for the distance. Shorter, high-throughput links and longer-range farm-to-shed links call for different hardware. We size the equipment to your actual distance and speed needs rather than a one-size-fits-all box.
• Proper outdoor cabling and power. Weatherproof, correctly glanded cable runs and PoE (power over the network cable) done properly, so water ingress and corrosion aren't a problem two summers from now.

• Units mounted low on a wall or fence post, then blocked by a vehicle, growing hedge, or new fence line months later.
• No allowance for seasonal foliage, so the link that worked fine in winter drops out completely by summer.
• A basic indoor WiFi extender used to try to bridge a real farm-to-shed distance, well outside what it was ever built for.
• Cabling run without proper outdoor-rated glands or weatherproofing, leading to corrosion and intermittent faults.
• Antennas roughly pointed "close enough," never properly aligned or tested under real load.

Mesh WiFi spreads coverage around inside one building or property using multiple nodes on the same network. A wireless bridge is different: it's a dedicated point-to-point link between two separate locations, effectively an invisible cable carrying your internet connection from one building to another. If you need coverage throughout your house, that's mesh. If you need to get your connection to a separate shed, workshop or second dwelling, that's a bridge.

Yes, with the right setup. Rather than a simple point-to-point link, larger properties often use a more powerful base station as a hub, with several remote buildings connecting back to it. We'll usually pair this with a network switch at the hub location so multiple bridges or access points can share the one connection cleanly.

No, that's the point of a wireless bridge. It shares your existing connection across a wireless link, so the remote building gets full network access without paying for or installing a second internet service.

A bridge needs a reasonably clear path between the two mounting points, so obstructions matter. Often this is solved with higher mounting or repositioning slightly. On some sites the path genuinely isn't workable, and we'll tell you honestly if a second connection or a different approach makes more sense than forcing a bridge that won't be reliable.

We supply, mount and configure the full bridge as part of the job, using Ruijie, TP-Link and TP-Link Omada equipment matched to your distance, speed needs and site conditions.

No, we don't do groundworks or trenching. If a wired connection is the better fit for your site, that digging needs to be arranged separately. We can supply, terminate and configure the network cable and equipment once it's in the ground, or advise on the right cable to use if you're organising a contractor yourself.

It's quoted per job. Distance, mounting height, and how much cabling and equipment the site needs all affect the price, so we confirm the full cost after the site survey, before any work begins.